ISI ON.
The pre-assembled sealing tray.
ISI ON was specially developed for the fast and secure sealing of shower trays and bathtubs. Even difficult and hard-to-reach areas can be easily and permanently protected. Available in five convenient standard sizes.
Area of application
Difficult-to-seal, uneven areas under shower trays can be sealed quickly, easily, and neatly with ISI ON.
Pipe penetrations
Secure sealing of the pipe penetration through collar formation of the sleeve.
Wall connection
Two-part release film: The sleeve can first be easily positioned and then fully bonded to the substrate.
Connection
Easy connection to the surface waterproofing.
Ready
In just a few steps to an optimally sealed shower tray or bathtub.
The ISI ON waterproof tray is available in 5 standard sizes for a variety of installation situations.
Left installation variant
Product variants
Bathtubs
180 x 80 cm
Order number
180L
Bathtubs
170 x 75 cm
Order number 170L
Shower trays
120 x 90 cm
Order number 120L
Shower trays
90 x 90 cm
Order number 90LR
(can be used on the left/right)
Shower trays
80 x 80 cm
Order number 80LR
(can be used on the left/right)
Right installation variant
Product variants
Bathtubs
180 x 80 cm
Order number 180R
Bathtubs
170 x 75 cm
Order number 170R
Shower trays
120 x 90 cm
Order number 120R
Shower trays
90 x 90 cm
Order number 90LR
(can be used on the left/right)
Shower trays
80 x 80 cm
Order number 80LR
(can be used on the left/right)
Recess installation variant
Product variants
Bathtubs
180 x 80 cm
Order number 180UL
Bathtubs
180 x 80 cm
Order number 180UQ
Bathtubs
170 x 75 cm
Order number 170UL
Bathtubs
170 x 75 cm
Order number 170UQ
Bathtubs
120 x 90 cm
Order number 120UL
Bathtubs
120 x 90 cm
Order number 120UQ
Shower trays
90 x 90 cm
Order number
90U
Shower trays
80 x 80 cm
Order number
80U
Freestanding installation variant
Product variants
Bathtubs
180 x 80 cm
Order number 180F
(horizontal, vertical, or completely free possible)
Bathtubs
170 x 75 cm
Order number 170F
(horizontal, vertical, or completely free possible)
Shower trays
120 x 90 cm
Order number 120F
(horizontal, vertical, or completely free possible)
Shower trays
90 x 90 cm
Order number
90F
(horizontal, vertical, or completely free possible)
Shower trays
80 x 80 cm
Order number
80F
(horizontal, vertical, or completely free possible)
Installation.
It’s simple.
Remove or level out unevenness with a spatula.
Prime the wall and floor surfaces to ensure good adhesion.
Thoroughly clean the substrate.
Cut off protruding remnants of the screed edge strip with a utility knife.
Important: Place the included fleece on the substrate under the waterproof tray to protect the foil from damage.
Use a spirit level to mark the height around the perimeter where the waterproof tray will be placed.
Measure the position of the drain and mark it on the foil of the waterproof tray.
Use a circle cutter to cut the opening for the drain in the foil (make the cut on a clean, flat surface to avoid tearing). Alternatively, scissors or a punching tool can be used.
First, slide the waterproof tray over the drain and position it. Then, peel off the narrow release paper and place the butyl strip along the marked line.
Then remove the wide release paper and fully adhere the fleece lining.
Apply the fleece lining to the substrate as smoothly and without tension as possible, and press firmly by hand or with a roller.
The fleece lining should be integrated into the adjacent surface waterproofing with a minimum overlap of 5 cm. Done.